PL-AD-160 High Quality HIFI Digital Class D Power Amplifier Module 2x80W MA12070

Description

Description
PL-AD-160 High Quality HIFI Digital Class D Power Amplifier Module 2x80W MA12070 Digital IIS Input
Description:
PL-AD-160 is a high-end digital power amplifier product based on MA12070 solution. MA12070 is a highly efficient fully integrated digital audio power amplifier IC based on multi-level switching technology. With enhanced design and production standards, the PL-AD-160 series of products can ensure high reliability and stability throughout the entire life cycle. It can provide first-class audio performance in a small package, suitable for design engineers to develop products for home and professional audio applications.
Features:
1. Multi-level switching technology with 3-level and 5-level modulation makes the solution unparalleled in power consumption and energy efficiency-optimized for power consumption when playing music, making it extremely low energy consumption.
2. 2x80W peak output power (26V PVDD, RL = 4Ω, 10% THD+N level), an ultra-compact, highly integrated solution-a real high-power small body.
3. Flexible realization of 2.0 (2*80W), 2.1 (1*80W+2*40W), 4.0 (4*40W), 1.0 (1*160W) channel output level configuration through the on-board dip switch.
4. The fourth-order feedback error control can provide better gain and suppress errors better than the traditional second-order loop, thereby ensuring extremely low signal distortion and excellent audio performance, even if the power supply is not ideal (noise or ripple), still ensuring low distortion, high sound quality and stability and reliability.
5. <160mW idle power dissipation (26V PVDD, all channels are switched); when the power is 2W, the efficiency is >80% (1kHz sine wave, 8Ω); when the power is full power, the efficiency is >91% (1kHz sine wave, 8Ω).
6. Audio performance (PMP2): >110dB SNR (A-w, relative to 1% THD+N power level), without the need for complex dynamic follow-up power supply design (conventional audio power design solutions that improve energy efficiency).
7. 45µV output integrated noise (A-w), no low-pass filter (LPF) is required in most applications.
8. When the output level is high, THD+N is 0.004%.
9. I2C control (four optional addresses for the DIP switch on the board), which can be connected to the MCU to control the working mode of the chip, achieving a balance between performance and power consumption, and can be customized in various applications.
10. Built-in protections: undervoltage lockout, overheat warning/error, short circuit/overload protection, power stage pin to pin short circuit, error report via serial interface (I2C), and DC protection.
11. Four-layer immersion gold PCB + anodized heat sink, with excellent heat dissipation and extremely low EMI.
12. Module size: 80 x 60 x 35mm (LxWxH)
Applications:
1. Portable speakers: battery powered speakers (battery is not included), mobile Bluetooth speakers, docking speakers, portable speakers, wearable speakers
2. Home audio: multi-room system, TV, sound column, home theater system, independent components
3. Voice control speaker
4. Professional audio: active monitor speakers, Power over Ethernet (PoE), multi-channel system
Advantages and Working Principle of Multi-Level Technology:
Although the efficiency of the traditional Class D audio amplifier has reached 90% and above, its relatively high power only achieves about 50% of the usual volume efficiency, and its demand for LC filters and heat sinks makes It takes up a lot of space (and the cost is higher). Multi-stage Class D amplifiers break these limitations. Its technological innovation has brought the following advantages:
› No need to output LC filter, smaller size and lower cost
› Improved common volume efficiency
› Significantly reduce power consumption and reduce heat dissipation
› Thanks to the high-frequency multi-level switch, the details of the sound source are preserved and the sound quality is improved.
This breakthrough amplifier product uses a multi-stage half-bridge power stage to achieve low power consumption in standby or near standby. Unlike traditional Class D amplifiers, each half-bridge power stage of this product has 4 transistors/MOSFETs (traditional Class D amplifiers only have 2pcs). These half bridges establish multiple PWM output stages through a single power supply (each MOSFET is driven by a separate PWM signal), which brings great flexibility and can configure the amplifier for the best power performance in any application. The flying capacitor (Cfly) located between the top and bottom MOSFETs is continuously powered by an independent circuit, so the voltage potential can be maintained at a fixed level. This "flying capacitor" basically acts as an additional power rail. In this way, each half-bridge power stage can establish a three-level output signal at the output switching node: 0 V, ½ PVDD, and PVDD.
1. DC power supply input terminal. The interface sequence from top to bottom is: VIN+, GND, VIN+, GND, two VIN+ and two GND are connected on the board to facilitate module cascading. The maximum input voltage of VIN+ is DC +26V, and the absolute voltage exceeding +27.5V will permanently damage the chip! To ensure the output power, please use a power supply of 200W and above. The minimum input voltage of VIN+ is +4V, and it is actually recommended to use a power supply above 6V.
2. Analog audio signal input terminal. The interface sequence from top to bottom is: IN0A, IN0B, GND, IN1A, IN1B, corresponding to the audio input terminals of SPEAK0A, SPEAK0B, SPEAK1A, and SPEAK1B respectively. The overall board gain is 20dB by default.
3. External control communication input terminal. The interface sequence from left to right is: SCL (clock pin of IIC), SDA (data pin of IIC), GND (ground), EN (the chip enters the reset state when pulled high), MUTE (mute output, effective when pull low).
4. IIC address selection pin, used to control multiple chip selection IIC addresses when multiple modules are used in parallel. Bit 1: AD0, bit 2: AD1.
5. Chip working mode selection. Bit 1: MSEL1, Bit 2: MSEL0. (Push up means 1)
Bit1/Bit2=0/0: 4-channel single-ended output (SE), at this time the maximum output power of each channel is 40W. The connection method is shown in the figure below:
Bit1/Bit2=0/1: 2 channels of single-ended output (SE) + 1 channel of half-bridge output (BTL), at this time, the power of each channel of single-ended output is 40W, and the power of half-bridge output channel is 80W. The connection method is shown below:
Bit1/Bit2=1/0:2-channel half-bridge output (BTL), at this time, the output power of each channel is 80W (factory default setting). The connection method is shown below:
Bit1/Bit2=1/1:1 channel dual half bridge output (PBTL), at this time, the single channel output power is 160W. The connection method is shown in the figure below:
6. Audio power level output terminal. The interface sequence from top to bottom is: SPEAK0A, SPEAK0B, SPEAK1A, SPEAK1B.
7. Power supply indicator LED. Green or blue LED, this LED should always be on after power on, indicating that the power supply of the module is normal.
Module Use Steps:
1. Correctly set the DIP switch at position 5 and correctly connect speaker hardware.
2. Set the voltage correctly at the interface 1 and connect DC power supply, you can see the LED at position 7 is lit.
3. Connect the input audio source to the interface 2 correctly.
4. Other parts generally do not need to be connected to work normally.
Package Included:
- 1 x Power Amp Module
Note:
- Green PCB pictured is for reference only. The actual items are designed with Black PCB boards.
- Items in Red or Black will be delivered at random. Please make sure that you don't mind before purchasing.
- Battery is not included.
Payment Terms
1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of auction closing.
4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.
Shipping Terms
- For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.
Return Terms
1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund.
2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA.
3. We reserve the right to refuse any returns for objective reasons.
Custom Duties & Taxes
1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility.
2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.
Feedback
1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers.
2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap.
On May-25-21 at 01:19:37 PDT, seller added the following information: